SparkIQ · Arduino
Syllabus Pricing FAQ
Two courses · 82 interactive lessons · no hardware needed

Learn Arduino Uno by wiring it and running it, right in your browser

Short lessons take you from your first blinking LED to buttons, sensors, displays, motors and your own libraries. Wire the circuit, run the code line by line, change it, and see what happens.

Lesson 3.3 · Make an LED blinkRunning
void loop() {
digitalWrite(13, HIGH);
delay(500);
digitalWrite(13, LOW);
delay(500);
}
Pin 13 is HIGH, so the LED is on. Change the delay and watch it respond.
82
interactive lessons in two courses
15
sections, from blink to input devices
0
parts to buy to start learning
Phone
friendly, works on any screen

Every lesson works the same way

You do not just read about Arduino. In each lesson you build the circuit and watch your code run.

STEP 1
Wire it
Connect each wire on a virtual Uno, one step at a time, with the circuit diagram beside you.
STEP 2
Run the code
See each line highlight as it runs, with a live graph, Serial Monitor or scope showing the result.
STEP 3
Experiment
Change values in the code, turn a knob, press a button, and see what happens straight away.
STEP 4
Challenge and quiz
Finish with a short challenge and a quiz, so you know you understood before you move on.

Syllabus

Three courses, 21 sections and 111 lessons, in the order you should learn them. Level 1 (sections 1 to 9) covers the basics. Level 2 (sections 10 to 15) goes intermediate. Level 3 (sections 16 to 21) is advanced. Each course is sold separately, and each has free lessons to try.

Level 1 · Basics
1
Getting started
Free
What a microcontroller is, a tour of the Uno, installing the IDE, your first Blink upload, setup() and loop().
5 lessons
2
Electronics basics
Free
Voltage, current and resistance, Ohm's law, choosing an LED resistor, breadboard connections.
4 lessons
3
Digital output
pinMode, digitalWrite, blinking an LED, delay(), blink patterns and SOS.
5 lessons
4
Buttons
Push buttons, pull-up and pull-down resistors, toggling an LED, debouncing with delay and millis().
5 lessons
5
Variables and decisions
Variables, data types and overflow, if and else, comparison operators, a traffic light project.
5 lessons
6
Loops and arrays
for and while loops, break and continue, arrays, an LED chaser project.
5 lessons
7
Serial Monitor
Printing from the Uno, baud rate, reading input from the computer, a button press logger.
4 lessons
8
Analog input
Analog versus digital, analogRead and the ADC, potentiometers, map(), light sensors and noise, an automatic night light.
6 lessons
9
PWM and colour
PWM, fading, dimming with a knob, gamma, RGB colour mixing, an auto-dimming night light.
6 lessons
Level 2 · Intermediate
10
Better programming
Functions, parameters and return values, constants, strings, why delay() blocks, millis() timing, a three-blinker project.
7 lessons
11
Displays
7-segment display, the 74HC595 shift register, 16×2 LCD, I2C LCD, OLED graphics, an uptime clock.
6 lessons
12
Sensors
TMP36 temperature, a thermostat with hysteresis, HC-SR04 distance, a parking sensor, PIR motion, a smart fan.
6 lessons
13
Motors and loads
Transistor switch, DC motor speed, relay module, servo sweep, servo with a knob, motor direction with an H-bridge.
6 lessons
14
Memory and libraries
Flash, SRAM and EEPROM, saving memory with F(), keeping values through a reset, EEPROM wear, writing your own class, a boot counter.
6 lessons
15
Input devices
4×4 keypad, rotary encoder, joystick, infrared remote, many buttons on one pin, a parking sensor with LCD as the final project.
6 lessons
Level 3 · Advanced
16
Advanced analog
ADC reference and resolution, noise and the moving average, measuring battery voltage, measuring current and calibrating zero.
4 lessons
17
Interrupts and timers
External and pin-change interrupts, writing a safe ISR, timers and prescalers, a timer interrupt for fixed sampling, changing the PWM frequency.
6 lessons
18
Communication
UART between two boards, the I2C bus scanner, SPI, SD card logging, the DS3231 clock, reading a datasheet timing diagram.
6 lessons
19
Program design
State machines, non-blocking multitasking, splitting code into files, writing a simple class.
4 lessons
20
Power and hardware
Power options and current limits, regulators and battery life, sleep modes and the watchdog, decoupling, breadboard to perfboard.
5 lessons
21
Wireless and the next step
HC-05 Bluetooth control, reading phone commands, moving from Uno to ESP32, and the project: a battery data logger.
4 lessons

Made for complete beginners

If you can use a phone or a laptop, you can start. Every idea is explained from the ground up, from what a microcontroller is to why an LED needs a resistor.

Students and school kids
Learn electronics and coding together, at your own pace.
Hobbyists and makers
Build a solid base before you spend money on parts.
Teachers and parents
A ready-made, hands-on way to teach Arduino without lab hardware.

Three courses, each with its own price

Sold by Vedax Global.

Try the free lessons first. Start with Level 1 if you are new to Arduino. Level 2 is for you if you already know variables, if, loops, analogRead and PWM. Level 3 is for you if you are comfortable with millis(), libraries and sensors.

Arduino Uno course
Level 1 · Basics
₹499
₹999
Launch price for the first 30 students. The regular price is ₹999.
45 lessons in 9 sections
Sections 1 and 2 (9 lessons) are free
Wiring, code, experiments, challenges and quizzes
Works in your browser, including on a phone
[ACCESS PERIOD, e.g. lifetime access]
[REFUND POLICY, e.g. 7-day refund]
Enrol in Level 1
Pay by UPI, card or netbanking · [GST INVOICE NOTE]
Arduino Uno course
Level 2 · Intermediate
₹499
₹999
Launch price for the first 30 students. The regular price is ₹999.
37 lessons in 6 sections
The first lesson of every section is free
Wiring, code, experiments, challenges and quizzes
Works in your browser, including on a phone
[ACCESS PERIOD, e.g. lifetime access]
[REFUND POLICY, e.g. 7-day refund]
Enrol in Level 2
Pay by UPI, card or netbanking · [GST INVOICE NOTE]
Arduino Uno course
Level 3 · Advanced
₹499
₹999
Launch price for the first 30 students. The regular price is ₹999.
29 lessons in 6 sections
The first lesson of every section is free
Interrupts, timers, SPI, I2C, SD logging, sleep modes
Ends with a battery data logger project
[ACCESS PERIOD, e.g. lifetime access]
[REFUND POLICY, e.g. 7-day refund]
Enrol in Level 3
Pay by UPI, card or netbanking · [GST INVOICE NOTE]
Best value
All three levels, one price
Levels 1, 2 and 3: 111 lessons in 21 sections, from your first Blink to a battery data logger. One purchase, one access code, every lesson unlocked.
Bought separately at the launch price the three levels cost ₹1,497, and at the regular price ₹2,997.
₹1,099
₹2,997
Enrol in all three levels
Pay by UPI, card or netbanking · [GST INVOICE NOTE]

Questions

Do I need an Arduino board?
No. The lessons use a virtual Arduino Uno in your browser, so you can learn everything without buying any parts. When you later buy a board, what you learned carries over.
Can I learn on my phone?
Yes. The lessons are built to work on a phone screen as well as on a laptop.
I have never done electronics or coding. Is that fine?
Yes. Yes. Level 1 starts with what a microcontroller is and builds up one idea at a time.
What is free?
In Level 1, sections 1 and 2 (nine lessons) are free: the Uno board, installing the IDE, your first Blink upload and basic electronics. In Levels 2 and 3, the first lesson of every section is free, so you can see displays, sensors, motors, memory and input devices working before you buy.
Do I need Level 1 before Level 2?
You need the skills, not the purchase. Level 2 assumes you can use variables, if, loops, analogRead and PWM. If you are new to Arduino, start with Level 1. If you want all the levels, the bundle gives all three for ₹1,099.
What is in Level 3?
Level 3 is advanced: interrupts and timers, communication buses, power saving and a final data-logger project. It assumes Level 2 skills: millis(), libraries, sensors and displays. The bundle gives all three levels for ₹1,099.
How do I get help if I am stuck?
Email help@vedaxglobal.com with your name, the lesson number and what you see on screen. A screenshot helps.
© SparkIQ, a brand of Vedax Global · help@vedaxglobal.com
[TERMS][PRIVACY POLICY][REFUND POLICY]